Run more cans.
serve more customers.
with the Trash Cat 47-14 roll-off dumpster hoist
Trash Cat 47-14 was built to solve the issues experienced with a 47” rail system truck and trailer setup.
Its faster cycle times, 8-ton lift capacity, and a winch that’ll pull a fully loaded 20-yard can across the ground without breaking a sweat, mean you can spend your time hauling cans, not waiting on your equipment to keep up.
A hoist designed to outlast multiple truck chassis, the Trash Cat 47-14 allows you to get more from your dumpster fleet. Its 47” rails are compatible with U-Dump and Texas Pride dumpsters allowing you to get away from the truck & trailer setup.
We wanted to haul cans,
not wait on equipment.
The Trash Cat 47-14’s faster cycle times significantly increases your daily hauling capacity allowing you to service more customers and give your brand the trust its name deserve
TrashCat 47-14 Specifications
| Spec | Hydraulic | Electric |
|---|---|---|
| Rail Width | 47" – fits Texas Pride & U-Dump | 47" – fits Texas Pride & U-Dump |
| Dumpster Lengths | 12' & 14' | 12' & 14' |
| Lift Mechanism | 16k scissor lift | 16k scissor lift |
| Winch | Warn 15k Hydraulic | Warn 15k Hydraulic |
| Hydraulic Pump | PTO wet line (not included) | 2gmp @ 3000psi (included) |
| PTO Requirement | 12gpm @ 3000psi | None |
| Controls | Switch panel behind cab | Switch panel behind cab |
| Control Valve | Solenoid-operated, pre-installed | N/A |
| Master Disconnect | N/A | Included |
| Tilt Frame | 6 x 2 x 1/4" steel | 6 x 2 x 1/4" steel |
| Subframe | 4 x 3 x 3/16" steel | 4 x 3 x 3/16" steel |
| Dump Angle | 45˚ minimum | 45˚ minimum |
| Lift Capacity | 16,000 lbs | 16,000 lbs |
What People Are Saying
-
Communication was top-notch and the final outcome was even better than we imagined. A great experience all around.
— Former Customer
-
Their attention to detail and commitment to quality truly stood out. We’ve already recommended them to others.
— Former Customer
-
Every detail was thoughtfully executed. We're thrilled with the outcome, and have already recommended them to others.
— Former Customer
Also works with
Freightliner M2
Ford F650 & F750
Mack MD6 & MD7
Peterbilt 535 & 536
Kenworth T180 & T280
International CV & MV Series
Hino L-Series
Isuzu N-Series
We Build It
Option 1:
Buy a turn-key truck built by us
Starting at
$85,000*
Option 2:
Bring us your truck and we upfit it
Starting at
$45,000*
How to Buy
You Build It
We ship you a DIY kit, and you partner with an upfitter near you or install it yourself.
HOW IT WORKS
We advise you on truck selection
We ship you a kit
DIY install or partner with a local upfitter
Haul trash!
starting at
$40,000*
*budget options available
You’ll talk to someone who actually built this thing.
Call Zach.
One conversation covers everything — which truck fits your operation, financing, and how to get it to you. No runaround, no guessing.
Get a straight answer on which truck, which configuration, and which path is right for your operation
Sort financing with our guy who knows these trucks
Pick up or we ship it – your call
Hoist Spec Deep Dive
Works with Your Truck
| Spec | Requirement | |
|---|---|---|
| Cab to Axle | 120" minimum | |
| Cab to End of Frame | 167" – 171" | |
| Frame Height | 30"-37" | |
| Frame Width | 34.5" maximum | |
| Spring Hanger to End of Frame | 6" minimum |
Compatible: Ford F-550, Ford F-600, Ram 5500, Chavy 6500, and most 26,000lb GVWR trucks
Works with Your Cans
| undefined | Value | |
|---|---|---|
| Rail Width | 47" – fits Texas Pride & U-Dump Systems | |
| Dumpster Lenghts | 12' and 14' | |
| Lift Capacity | 16,000 lbs | |
| Dump Angle | 45˚ minimum |
Note on 16’ Dumpsters: A 16’ can is physically possible but not recommended on a 120” cab-to-axle hoist. If you’re running 16’ cans, talk to us before you order.
Load Distribution
Where your load sits relative to the axle matters for how your truck handles and what your registration allows. Here’s what we’ve measured:
| Spec | Forward of Axle | Rear of Axle | Cargo Center of Gravity |
|---|---|---|---|
| 12' | 83" (58%) | 61" (42%) | 11" forward of axle |
| 14' | 83" (49%) | 85" (51%) | 1" rear of axle |
How it’s Built
| Spec | Value | |
|---|---|---|
| Tilt Frame | 6 x 2 x 1/4" steel | |
| Subframe | 4 x 3 x 3/16" steel | |
| Rail Rollers | Internal, greasable, welded in place | |
| Winch | Warn 15k (electric or hydraulic) | |
| Tail Lights | DOT combination stop/tail/turn/reverse | |
| Ground Roller | Included | |
| DOT Bumper | Included |
Hydraulic Vs. Electric
| Spec | Hydraulic | Electric |
|---|---|---|
| Lift Mechanism | Scissor | Scissor |
| Winch | Warn 15k Hydraulic | Warn 15k Electric |
| Hydraulic Pump | PTO wet line (not included) | 2gpm @3000psi (included) |
| PTO Requirement | 12gpm @3000psi | None |
| Controls | Switch panel behind cab | Switch panel behind cab |
| Master Disconnect | N/A | Included |
| Control Valve | Solenoid-operated, pre-installed | N/A |
What Ships Pre-Installed
All controls, hydraulics, and electrical components arrive on the hoist ready to connect. Electric version requires battery hookup and light harness connection only. Hydraulic version requires PTO, pump, and supply/return lines — control valve ships pre-installed.
Shipping Dimensions
| Spec | L | W | H | Weight |
|---|---|---|---|---|
| Host Only | 219" | 68" | 30" | 2,500 lbs |
| With Tarp Mast | 219" | 68" | 30" | 2,6000 lbs |
Mounting Hardware
Mounting Kit included. Weld-on tabs, frame spacer shims, and 1/2” Grade 8 bolts. Weld tabs to hoist subframe, bold to truck frame.